BakFlip MX4 for Ford F-150 | Hard Folding Tonneau Cover
Our BakFlip MX4 is engineered specifically for Ford F-150 owners who demand maximum protection without sacrificing bed access. This hard folding cover features our exclusive aluminum panel construction with a matte finish that resists scratches, dents, and UV damage season after season.
The four-panel design folds completely open for full bed access, or you can configure it partially for oversized cargo. We built the MX4 with an automatic latch system that secures at the tailgate, plus heavy-duty aluminum support struts that hold panels upright in any position. Installation takes about an hour with basic hand tools—no drilling required on most F-150 models from 2015 to present.
Every MX4 cover sits flush with your truck's bed rails for a low-profile look that improves aerodynamics and fuel efficiency. The integrated drain channels route water away from your cargo, while our dual-action tailgate seal keeps moisture and dust out even during highway driving.
MX4 F-150 specifications
Panel Construction & Weather Protection
We manufacture every MX4 panel from heavy-gauge extruded aluminum, then apply a fiber-reinforced polymer coating that creates a scratch-resistant matte surface. This construction method delivers the strength of a one-piece cap with the convenience of a folding design. Each panel connects with reinforced aluminum hinges rated for 50,000+ open/close cycles.
The integrated drain system channels moisture through hidden gutters that exit at the rear of your F-150 bed. Our dual-seal design places EPDM rubber gaskets at every panel junction and around the entire perimeter, creating a weatherproof barrier that keeps cargo dry during rain, snow, and car washes. The tailgate seal compresses automatically when you close the cover, forming an airtight bond that also reduces wind noise at highway speeds.
Cargo Access & Bed Compatibility
Full-Length Opening
The four-panel folding system on the MX4 lets you configure bed access exactly how you need it. Fold one panel back for quick access to the front third of your bed. Open two panels to load cargo from the side. Fold all four panels completely against the cab for unrestricted access to the entire bed—panels stack just 11 inches from the cab, so you retain nearly full bed length.
Oversized Load Positioning
When you’re hauling tall cargo like toolboxes or ATVs, the MX4 panels lock upright at 90 degrees in any configuration. The heavy-duty support struts hold panels securely without external props, and you can still close your tailgate with panels folded. We designed the cover to work with most aftermarket bed accessories including tie-down systems and bed extenders.
Installation & Rail System
We engineered the MX4 with a clamp-on rail system that eliminates drilling on most Ford F-150 configurations. The installation process takes 45-60 minutes with standard hand tools. You’ll mount the side rails first using our adjustable clamps that grab your truck’s existing bed rails, then position the cover panels and connect them with the hinge system.
Each MX4 kit includes pre-assembled side rails, all mounting hardware, a tailgate seal kit, and detailed instructions with photos specific to your F-150 bed length. The rails come with built-in LED light ports if you want to add our BakBox lighting accessories later. We also include adjustment shims to ensure perfect alignment on trucks with bedliners or spray-in coatings.
Complete Your F-150 Bed Setup
Rated 4.8 by verified buyers
Common Questions About the MX4 F-150 Cover
Yes, the MX4 fits all F-150 Lightning models with standard bed configurations. The cover mounts to the factory bed rails just like gasoline F-150 models. You'll select your bed length (5'7" or 6'7") when ordering. The Lightning's power frunk doesn't affect installation or operation.
The cover works with the Lightning's power tailgate feature—the automatic latch engages normally when you close the tailgate remotely or manually.
Absolutely. The MX4 clamp system fits over most spray-in bedliners including Line-X, Rhino Lining, and Bullet Liner. The clamps grab the top of your bed rails where the liner typically doesn't cover. We include adjustment shims to account for liner thickness and ensure the cover sits level.
For textured liners, you may want to place the included foam tape on the bottom of the rails for a tighter seal. The installation instructions include specific guidance for bedliner compatibility.
The MX4 is rated for 400 pounds of evenly distributed weight when fully closed and latched. This capacity is sufficient for snow accumulation, light camping gear, or properly secured cargo carriers. Never exceed this limit or concentrate weight on a single panel.
If you regularly carry rooftop loads, we recommend distributing weight across all four panels and using tie-down points at your truck's bed rails rather than the cover surface.
Yes, the MX4 is compatible with Ford's factory BoxLink tie-down system and adjustable bed dividers. The cover mounts above these accessories so they remain fully functional. You can still use the BoxLink cleats and cargo organizers exactly as designed.
The cover also works with most aftermarket bed dividers and storage systems that mount to the bed rails. Just ensure any dividers don't extend above the rail height where the MX4 clamps attach.
Clear heavy snow from the panels first, then check if ice has bonded the seals to the panel edges. If panels won't lift, tap gently along the seam with a rubber mallet to break the ice seal—never force the automatic latch or pull upward on frozen panels.
We recommend applying silicone spray to the EPDM seals before winter begins. This prevents ice from bonding as strongly. The aluminum panels and hinges are designed for cold weather operation and won't crack or become brittle in freezing temperatures.
Yes, the MX4 works with our BakBox 2 toolbox that mounts directly through the cover near the cab. The toolbox bolts to the cover's support rails and doesn't interfere with panel folding. You can also install most fifth-wheel hitches and gooseneck adapters—just fold the front panel up to access the mounting points.
For roof racks and cargo carriers, we recommend systems that clamp to your truck's cab and bed rails rather than mounting through the tonneau cover itself.
Both covers use our aluminum panel folding design, but the MX4 features a matte black finish while the G2 has a gloss finish. The MX4's industrial coating resists scratches better for work truck applications. The G2 includes built-in LED light bars along the rails for bed illumination.
Functionality and weather sealing are identical between both models. Choose the MX4 if you prefer the matte look and don't need integrated lighting. Choose the G2 if you want the gloss finish and LED bed lights. Both carry the same 3-year warranty.